When you have a traditional water softener, it adds a small amount of salt to your water. Calcium and Magnesium hardening are needed to replace Sodium ions. This is a must-read if you want to understand why some salts are too powerful for your body to handle. Adding 35 mg of sodium to your water means that it will become less alkaline.
To compare, a slice of bread contains between 100 and 230 mg of sodium. If your softener water tastes salty, there’s something wrong. You don’t want to drink salty water. It’s not pleasant, and it will only be around for a short while. The sooner you solve the problem the better.
The reasons behind salted water coming after regeneration are quite varied. Some are mechanical or structural while others could be related to the quality of the water.
What Causes Salty Water After Regeneration?
Many people think that using a water softener makes your water taste salty. However, many water softeners actually make your water taste fresh. The taste of salt means that there is something wrong with the water system, like dirty pipes or a broken connection. If the water isn’t changed often enough and doesn’t stay clean, the salt water will build up and can cause a problem.
Before diagnosing the issue, check your environment to be sure it’s safe to work in. Turn off the water to the softener, and shut off the valve that allows the water to bypass the system, diverting water away from it.
Clogged Injector
If your injector valve appears clogged, the first thing to check is your injector valve. The saltwater injector comes with three horizontal and one vertical hole, making it easier to clean.
The injector valve is a delicate part, so make sure you’re taking care when you’re cleaning out the holes. Use a wooden toothpick or a toothbrush, and avoid using metal objects that can make the holes bigger. If the blockage is in your new valve, it’s a good idea to buy a new one.
Drain Line Flow Control Clogged
You can do this by turning the water faucet on and off while you’re in the shower. This button is located inside the system’s elbow, and it can easily become blocked with salt and sediment.
You can remove and clean it out if necessary. It’s important to be careful when cleaning out your drain line. There’s no replacement for hard work! Don’t let anything stop you from accomplishing your goals in life.
Drain Line is Clogged or Crimped
If you still have a salty water taste, look at the drain line in your water softener. It may be clogged. The pipe that runs under the sink can become kinked and crimped, which prevents water from passing through.
If you can smell the rotten egg odor, you need to get a root canal treatment. Press to check for blockages that could prevent a proper flow of water. Another issue you might look for is a drain line that is too long. Your drain should be at least 6 feet long, but if your drain is longer, it will be better able to drain your tank.
Brine Line Clogged or Crimped
Your brine line may become clogged with sodium and sediment from your brine solution. The brine line could also be crimped to prevent the brine solution from properly flowing through.
Your water could taste salty because there’s a build-up in your pipes. To prevent this, make sure your system is properly flushed. Follow the steps above to check for kinks and clogs. You’ll have to purchase a new part if you notice any major damage.
Bad Brine Valve
Abrasion or cracking of the brine valve components, such as the brine and downflow pistons and the spacer stack, may occur, potentially exposing you to the high-pressure gases When this happens, salt solution can get into the resin container, where it might end up soaking up more salt than necessary.
To remove the drain and brine from your elbow, open the valve and turn off the water supply. Drain the water from your elbow. If you notice any “chiming” noises from your engine, you’re probably dealing with a piston or spacer stack issue. If your car isn’t working properly you need to get it fixed.
Excessive Water in the Brine Tank
If your water hardening system malfunctions, your brine tank may overflow with water. Your system might be leaking salt from your tank. Make sure to unplug your salt dispenser and check for leaks in your plumbing.
It’s time to check your brine tank. There should be about 6″ of water in there, and 10″ maximum. If you don’t drink enough fluids, your body will absorb too much salt. You can empty the water from a faucet or sink, or just a bucket or container, if you have one. Clear out all blockages, and set up a new Amazon FBA account if you have one. This will prevent the problem from happening again.
Improper Programming of Control Head
Once you’ve installed your hard water softener, the most important task is to input the right settings into the control head. You need to input the correct water hardness level to allow the system to perform regeneration cycles according to this information.
Mechanical programming cannot also be affected by power outages. The setting for your pre-programmed settings could change due to electricity problems or the meddling of little children. Either way, you should be careful not to accidentally add too much salt to your drinking water.
Brine Cycle Interrupted
In order to regenerate a water softener, it is important to wash the resin bed by filling the resin tank with a salt solution. Bring is usually takes between 30 and 100 minutes. Sodium chloride (also known as table salt) is used in the creation of ice cubes, margarines, sauces, and many other foods.
Water Being Used During Regeneration
You should usually set your water softener to regenerate when it’s least likely to be used, between 2 and 3 am. If the timer is set to perform system regeneration at a different time, you may end up drinking saltier than usual water.
You might also wake up in the night and use your water, whether to pour yourself a glass of water, to use the bathroom, or to answer nature’s call. You can remove salt from the water softener if you regenerate the machine frequently. In the morning, your water will come out of your faucets. To resolve this, just open your faucet and let the water run for a couple of minutes, until your water is back to its normal taste.
Low Water Pressure
If your water pressure is lower than 30 PSI, it might not be fast-flowing enough to properly get through your softener. You’ll know whether you need a water softener if your water pressure is low or high, but most water softeners are best for a water
If your well water comes out weak, you need to fix it right away. You should check your water pressure once or twice per year, just in case you need to replace the washer or a main water line. It’s best to buy a booster pump to help get water flowing through your pipes faster.
Incoming Water Has High Sodium Content
Rarely, the problem may be with the drinking water that’s entering your home. If your water supply contains a high level of sodium already, adding a water softener will only increase it further. It’s a good idea to test your water for sodium ions before it goes through your water softener.
Frequently Asked Questions
How much sodium should my water contain?
The exact amount of sodium required to soften your water depends on your hardness. Harder water means more calcium and magnesium. You need more sodium ions to replace those mineral ions, and the more hard water you have in your system, the more you’ll need.
You can calculate how much sodium will be added to your drinking water after you know your hardness level in GPM. And then use this calculation: Water hardness x sodium added per gallon / 16 (cups in a gallon) = amount of sodium in one 8-ounce glass.
Take for example, if you have a water hardness of 11 GPG and you add 30 mg of sodium per gallon, the calculation would look like this: 11 x 30 / 16 = 20.
How can I reduce sodium consumption?
This book will tell you why your water tastes salty. It explains how water reacts to certain minerals, and it will show you how to fix the problem.
You might also have a medical condition that makes it difficult for you to consume sodium where possible. Restricting your sodium intake is one of the best ways to reduce the chances of developing high blood pressure. If you want to remove rust stains from cast iron cookware, you should add potassium chloride to your hard water softener instead of sodium.
Potassium chloride is salt-free and is a good alternative for people who don’t like salt in their water. You can also filter your softened water to remove excess sodium before drinking it. There’s really only one way to achieve this. The filter will eliminate more contaminants like chlorine and lead from your water.1.
You could also use a reverse osmosis unit at the end of the water line to purify water, if you want to avoid purchasing another one for the refrigerator and you want to avoid running the Depending on the hardness of your water, you can opt to use a reverse osmosis filter as well.
They are as effective at removing calcium and magnesium as water softeners. If you have particularly hard water, a reverse osmosis system may not be suitable as the high mineral content of the water could cause harm to the RO membrane.